Telestream PRISM MPI-UP PHY-12G Field Upgrade Instructions Download

Page: 3 / 40

PRISM Field Upgrade Kit Instructions

Table of Contents

Important compliance and safety information ....................................................... ii

Kit description ........................................................................................................ 1

Supported upgrades ......................................................................................... 1

Kit parts list ..................................................................................................... 1

MPI hardware upgrades ......................................................................................... 2

Recommended tool list .................................................................................... 2

Upgrade the PRISM MPI Eye mezzanine board ............................................. 3

MPX hardware upgrades ...................................................................................... 10

Recommended tool list .................................................................................. 10

Upgrade the PRISM MPX Eye mezzanine board.......................................... 11

Upgrade the instrument firmware ........................................................................ 21

Upgrade the software license ............................................................................... 24

Verify the hardware upgrade ................................................................................ 25

Summary of Contents for PRISM MPI-UP PHY-12G









































Search results

Summary of Contents for PRISM MPI-UP PHY-12G

Reviews:

Related manuals for PRISM MPI-UP PHY-12G

Brands by name

Popular brands

Telestream PRISM MPI-UP PHY-12G, Field Upgrade Instructions

Search results

Summary of Contents for PRISM MPI-UP PHY-12G

Reviews:

Related manuals for PRISM MPI-UP PHY-12G

Brands by name

Popular brands