background image

ISOBUS ECU 1224 User and Instruction maual

 |  

 

P00801545     Rev:02          SW:1.0.0                     

 

58 

 

19

 

WARRANTY 

 

This product has been designed and manufactured using the most modern techniques. The 

manufacturer guarantees the products for 24 months from the date of purchase. 

Tecomec S.r.l. guarantees that ISOBUS ECU 1224 SPRAYER labeled products are covered 

against manufacturing defects during the following periods. 

19.1

 

Warranty periods

 

 

Finished products 

– 2 years from Invoice date to end user 

 

Warranty on parts or reparation made during warranty period will end at the end of 

initial warranty period. 

19.2

 

Product warranty terms

 

1.

 

The warranty period starts at the date of purchase. The guarantee will be applied 

upon presentation of the purchase invoice. The manufacturer, acting through the 

sales and technical assistance network, shall replace free of charge any defective 
component. The warranty does not modify the purchaser’s rights as established 

under legislation governing the consequences of defects in the product. 

2.

 

The technical staff will intervene as soon as possible within the time limits granted by 

organizational arrangements. 

3.

 

Any claim under the warranty, must include details of invoice or receipt showing the 

date of purchase. 

4.

 

The manufacturer excludes consumables and parts subject to normal wear and tear.  

5.

 

The guarantee excludes intervention for updating and improvement of product. 

6.

 

The warranty does not cover the tuning maintenance interventions which should 

occur during the period of guarantee. 

7.

 

Any damage caused during transport must be reported immediately to the carrier or 

warranty will be void. 

8.

 

The warranty does not cover any damage, direct or indirect, caused to people or 

things 

9.

 

The warranty is void in the event of: 

 

Obvious lack or wrong installation or maintenance. 

 

Use of not original spare parts or accessories 

 

Interventions carried out by non-authorized personnel. 

 
 

Summary of Contents for GEOline 8410073





































































Reviews: