manualshive.com logo in svg

Tecomec GEOline 8410073, Instruction And User'S Manual, Page: 40 / 68

Share
Download
Tecomec GEOline 8410073 Instruction And User'S Manual Download Page 40

ISOBUS ECU 1224 User and Instruction maual

 |  

 

P00801545     Rev:02          SW:1.0.0                     

 

39 

 

Following the description of LED Status 

Table 13 

Status 

LED Light description 

Off 

Always turned OFF 

On 

Always turned ON 

Flash Slow 

1500 ms ON, 1500 ms OFF 

Flash Normal 

700 ms ON, 700 ms OFF 

Flash Fast 

250 ms ON, 250 ms OFF 

Pulse 1 

One pulse (200 ms ON, 200 ms OFF)followed 1000 ms OFF 

Pulse 2 

Two pulses (200 ms ON, 200 ms OFF) followed 1000 ms OFF 

Pulse 3 

Three pulses (200 ms ON, 200 ms OFF) followed 1000 ms OFF 

Pulse 4 

Four pulses (200 ms ON, 200 ms OFF) followed 1000 ms OFF 

 

9.8.1  Led L1: main status 

L1 display the status of the ISOBUS ECU 1224. The following notation is used: 

•

 

IDLE status

: the driver is ready, but no treatment is running 

→

Flash SLow

 

•

 

WORK status

: the driver is managing a treatment (main valve open) 

→

Flash Fast

 

 

9.8.2  Led L2: ISOBUS connection status 

L2 display the current connection status of the ISOBUS ECU 1224 with the ISOBUS network. The 
following notation is used: 

•

 

OFFLINE status

: the ISOBUS network is not detected 

→

Flash Fast

 

•

 

ONLINE status

: the ISOBUS network is detected 

→

On

 

 

9.8.3  Led L3: error codes 

L3 display the last error code detected by the ISOBUS ECU 1224 driver. It uses the 

Pulse 1÷4

 

modes to indicate specific errors and the 

Off

 state for no errors. 

 

 

 

Summary of Contents for GEOline 8410073





































































Reviews:

No comments