Tecomec GEOline 8410073 Instruction And User'S Manual Download Page 49

Page: 49 / 68

ISOBUS ECU 1224 User and Instruction maual

P00801545 Rev:02 SW:1.0.0

TROUBLESHOOTING

Table 14

DISPLAY

CAUSE

SOLUTION

The display does not turn on

There is not power.

Check the connections on the
power cable.

The indicator is turned off.

Press the turning on button.

The valves can not be controlled

The valves are not connected.

Connect the connectors

A valve does not open

The valve has not power.

Check the electric connection
and the functioning of the valve

The counter of the travelled
distance shown on the computer
is different from the real one.

Wrong programming

Check the speed sensor
configuration.

The reset of the treatment has
not been effectuated

Reset the treatment

The counter of the travelled
surface shown on the computer
is different from the real one.

Wrong programming

Check the bar width
programming

The reset of the treatment has
not been effectuated

Reset the treatment

The instant pressure is not
shown.

The indicator has not signal from
the pressure sensor

Check the connections with the
pressure sensor

Wrong installation of the pressure
sensor

Check the bottom scale
programming for the pressure
sensor

The instant pressure visualized is
inaccurate.

Wrong programming

Check the bottom scale
programming for the pressure
sensor

Wrong installation of the pressure
sensor

Check the connections with the
pressure sensor

The tank level visualized is
inaccurate.

The level sensor is not calibrated. Do the calibration.

Repeat the level sensor
calibration.

Wrong installation of the level
sensor.

Check the connection with the
level sensor

Led L1 (refer to figure 22) is
always Off

The ECU-1224 has an hardware
or software problem

Call the technical support

Led L2 (refer to figure 22) is
always Off

The ECU-1224 has an hardware
or software problem

Call the technical support

Led L2 (refer to figure 22)
remains always On (doesn’t
flash) when the ECU is
connected to the ISOBUS
network

Problems on ISOBUS network
connection

Verify that your Virtual Terminal
is correctly installed and turned
on.

If the problem persists, call the
technical support.

Leds L4 and L5 (refer to figure
22) remains always Off.

The ECU-1224 is not correctly
powered.

Check the ECU-1224 connection
cable.

Summary of Contents for GEOline 8410073





































































Search results

Summary of Contents for GEOline 8410073

Reviews:

Related manuals for GEOline 8410073

Brands by name

Popular brands

Tecomec GEOline 8410073, Instruction And User'S Manual

Search results

Summary of Contents for GEOline 8410073

Reviews:

Related manuals for GEOline 8410073

Brands by name

Popular brands