manualshive.com logo in svg

Tecomec GEOline 8410073, Instruction And User'S Manual

The Tecomec GEOline 8410073 is a top-notch product designed to meet all your cutting and sharpening needs. With its high-quality craftsmanship and innovative features, this manual chainsaw sharpener guarantees optimal performance. To ensure convenient and hassle-free usage, an Instruction and User's Manual is available for download, absolutely free, from manualshive.com.

Share
Download
background image

ISOBUS ECU 1224 User and Instruction maual

 |  

 

P00801545     Rev:02          SW:1.0.0                     

 

17 

 

8.3  Flowmeter installation 

The flowmeter is directly connected to ISOBUS ECU 1224 and measure flow in the control unit 
during a spraying treatment, it shall be correctly configured in the SETUP page of the user 
interface (refer to Flowmeter setup Chapter 9.3.2)  

The flowmeter shall be provided with a cable terminating with a 3-poles male connector, that will 
be plugged with the related female of the connection cable provided with ISOBUS ECU 1224. 
Sensor input plug is part of harness Connector C2 (Gray connector 24 pin), 

Label “F”

 

 

The pinout of the female connector provided with the ISOBUS ECU 1224 driver cable is the 
following 

Table 8 

PIN 

Description 

Color 

1 

GND 

BLACK 

2 

Power 

RED 

3 

Signal 

GREEN 

 

8.4  Pressure sensor installation 

The pressure sensor is optional. can be used for pressure measure or flow regulation. For specific 
applications, user can decide to use Pressure sensor instead of flow sensor. 

Sensor is connected to the ISOBUS ECU 1224 and can measure the liquid pressure during a 
spraying treatment, it shall be correctly configured in the SETUP page of the user interface (refer 
to chapter 9) 

The pressure sensor shall be provided with a cable terminating with a 3-poles male connector, that 
will be plugged with the related female of the connection cable provided with the ISOBUS ECU 
1224. Sensor input plug is part of harness Connector C2 (Gray connector 24 pin), l

abel “P”

 

The pinout of the female connector provided with the ISOBUS ECU 1224 driver cable is the 
following 

Table 9 

PIN 

Description 

Color 

1 

GND 

BLACK 

2 

Power 

RED 

3 

Signal 

GREEN 

 

8.5  Tank-level sensor installation 

The tank-level sensor is optional. Level sensor is noyt used for rate regulation. Level sensor is 
directly managed by the ISOBUS ECU 1224 driver and if installed to manage the detection of the 

Summary of Contents for GEOline 8410073





































































Reviews:

No comments

Related manuals for GEOline 8410073

Rayrun BR11 Quick Installation Manual preview
BR11
Brand: Rayrun Pages: 2
IDenticard 9000 Series Converting Instructions preview
9000 Series
Brand: IDenticard Pages: 2
3Ware 9000 Series Specification preview
9000 Series
Brand: 3Ware Pages: 2
UCS CAT Quick Start Manual preview
CAT
Brand: UCS Pages: 4
Jabra Link 14201-10 How Do preview
Link 14201-10
Brand: Jabra Pages: 4
Lawler 801 Installation & Maintenance Manual preview
801
Brand: Lawler Pages: 4
QTP 10900 Quick Start Manual preview
10900
Brand: QTP Pages: 2
National Instruments PXIe-8238 Getting Started Manual preview
PXIe-8238
Brand: National Instruments Pages: 6
National Instruments PXI-8231 Installation Manual preview
PXI-8231
Brand: National Instruments Pages: 6
Xantrex Trace C35 Installation And Operation Manual preview
Trace C35
Brand: Xantrex Pages: 56
Xantrex TrueCharge 2 Owner'S Manual preview
TrueCharge 2
Brand: Xantrex Pages: 2
Xantrex Freedom Sequence Owner'S Manual preview
Freedom Sequence
Brand: Xantrex Pages: 58
Xantrex Freedom e-GEN Checklist preview
Freedom e-GEN
Brand: Xantrex Pages: 4
Xantrex AGS Owner'S Manual preview
AGS
Brand: Xantrex Pages: 20
Parker PWD Series Operation Manual preview
PWD Series
Brand: Parker Pages: 38
Parker Racor RK 30770 Operation And Safety Instructions preview
Racor RK 30770
Brand: Parker Pages: 2
K&K M4700B Installation Instructions Manual preview
M4700B
Brand: K&K Pages: 10
Idemia MorphoAccess VP MD Quick User Manual preview
MorphoAccess VP MD
Brand: Idemia Pages: 29

Brands by name

Popular brands

Load more brands