25
TEC-67231-2 Technical description Prizrak-8xx BT
29
The input for keyless
bypass module
synching
It is used in exceptional cases during the alarm synching with a vehicle’s factory immobizer (refer to the
Integrator)
30
CDL «lock» input
A signal applied at this input triggers CDL locking
31
CDL «unlock» input
A signal applied at this input triggers CDL unlocking
32
CDL «lock/unlock»
input
A signal applied at this input locks the CDL if it is unlocked and unlocks the CDl if it is locked
33
Programmable logic
input
A signal applied at this input is processed by an operating algorithm created in the «Programming studio»
Programming sequence
1
Turn the ignition to the ON position.
2
Complete an authentication procedure.
It is possible to enter the default PIN code «2» with the built-in programming/reset button of the alarm in case if a vehicle hasn’t yet
travelled 10 km after installing the alarm.
3
Press and release the programming button 10 times within 10 seconds after an authentication procedure is complete in order to enter
the «Menu 1», the alarm will emit 3 beeps and the LED will flash 3 times. To enter the «Menu 1.2» press and release the programming
button 11 times, the alarm will emit 6 beeps and LED will flash 6 times to confirm that the «Menu 1.2» is successfully selected.
4
Select a desired option
№
within a programming menu. Press and release the programming button a number of times that corresponds
to the desired option №, the alarm will emit a certain number of beeps and LED flashes.
E.g., in order to advance from the
option №2
«Wired engine locking» to the option №16 «Number of brake pedal applications», press and release the programming button 14 times.
The alarm will inform about the new selected option number by a corresponding series of beeps and LED falshes.
In case if the option №
consists of two digits, the first digit is indicated with a long beep and the second digit is indicated with a short beep:
•
the option №10 is indicated with one beep;
•
the option №11 is indicated with 1 long beep, 1 second pause and 1 short beep.
5
Change the selected option setting to a desired one by pressing and holding the brake pedal. The alarm will inform about the current
option setting by a corresponding number of beeps, the beeps length will also change.
6
Change the option value by pressing and releasing the programming button number of times required to advance within the same option
from the current option value to a desired one. Keep in mind that after the last option value goes the first one. Release the brake pedal,
the alarm will stop indicating the setting of the option and will start indicating the current number of the option within the menu. Now
you may proceed to configuring another menu option or exit the programming menu.
7
The feature
№8
«Doors, hood, trunk» programming algorithm:
7.1
Set up any combination of doors, hood, trunk for indicating their statuses on the appropriate programmable output. In the
programming menu this algorithm is called «Doors».
7.2
With the brake pedal held proceed to option №8, the alarm will inform about the chosen option number by series of 8 beeps (2 times).
After that it will be emitting intermittent audible signals. As soon as you hear intermittent signals — release the brake pedal. The alarm
will keep emitting intermittent sounds. Open only those doors (you may do it in advance) which you need to be indicated on that output,
the doors you don’t want to be indicated should be closed. Depress the brake pedal again and keep it down, the alarm emits 8 beeps
— the doors are now assigned to the output. If you don’t press the brake pedal and exit the programming menu, the alarm will save
in its memory the previouse option value.
8
The feature
№10
(refer to the Table 8 «Programmable outputs configuration») «Vehicle’s OEM button pressure» programming algorithm.
Programming algorithm for feature №10 – Factory buttons. With the brake pedal held proceed to the option №10. The alarm will emit 2
series of 1 long beep, and then will start emitting short intermittent audible signals. Holding the brake pedal press a desired button (please
refer to the Integrator to check the list of available buttons for a specific vehicle). If the alarm recognizes the button, it stops emitting
intermittent signals and returns to a current option number indication by a series of 1 long beep. Release the brake pedal, the alarm will
start indicating a current Table 8 option number. If you release the brake pedal before the alarm has learned a button, the alarm will exit
this option, save previous option settings, and will go back to a current option number indication.
9
The feature
№15
– «Gear lever position» programming algorithm.
With the brake pedal pressed advance to the option №15. The alarm emits 2 series of 1 long and 5 five short beeps, and then will start
emitting short intermittent beeps. While still holding the brake pedal pressed, shift the transmission to a required position: «P, N, D»* or
«R» (gear lever might be set into the necessary position beforehand). For an automated gearbox — «R, N, D»* gear lever position may be
programmed, and for manual transmission you can only program «R» position. Release, then press again the brake pedal. The alarm will
stop emitting short intermittent beeps and returns to the current option value indication by a series of 1 long and 5 short beeps. Release
the brake pedal, the alarm will go back to the menu option number indication. If you do not press the brake pedal- the alarm will abort
programming of this option, save the previous settings and automatically exit the program mode.
10
Parking distance control button programming algorithm (PDC).
With the brake pedal pressed select the option №14 – Menu 1. The alarm will start emitting short intermittent beeps. Press and hold
the selected button for a certain amount of time (if the alarm recognizes the button, the system will stops emitting short beeps while
the button is being pressed):
•
Short button press control – hold the button for at least 2 seconds.
•
Long button press control (2.5 sec) – hold the button from 2 to 5 seconds.
•
Status button press control – hold the button for at least 5 seconds. Release the button, the alarm emits one beep and stops
indication.
Release the brake pedal, the alarm will return to to the current option number indication.
11
The feature
№46
«Heating turning on during remote start mode» (impulse control).
With the brake pedal held proceed to the option №46. The alarm will inform about the option status by 2 series of 4 long and 6 short
beeps. After that the alarm starts indicating the number of pulses which will be generated on the relative output for heating turning on.
•
1 pulse — one beep,
•
2 pulses — 2 beeps,
•
3 pulses — 3 beeps.
If you would like to change the number of pulses-release the brake pedal and press the PB a corresponding number of times and by
listening to the audible signals make sure that you have chosen the required number of pulses. Then press and hold the brake pedal
again — the alarm quits indicating the option status and starts indicating the current option number.
12
The feature
№50
«Output for the remote start».
While holding the brake pedal pressed proceed to the option №50. The alarm will indicate the current option value with two series of 5
long beeps. Thereafter, the alarm will start indicating the feature number according to the assigned remote start timing diagram. E.g.
the timing diagram №3 is set up by default, the output №4 is set up as «Key is in the ignition switch». For the otput «Key is in the ignition
switch» of the timing diagram №3 is assigned the value «2».
