19
TEC-67231-2 Technical description Prizrak-8xx BT
Table 7. Codes for programming menus
Menu name
Menu code
Number of
beeps
Designation
Menu 1
10
3
Hardware functions configuration
Menu 1.2
11
6
Programmable inputs/outputs configuration
Menu 2
12
4
User settings
Built-in sensors adjustment
8
5
Shock and tilt/displacement sensors adjustment
Remote engine start mode
settings
16
7
Remote engine start settings
Engine heater settings
17
8
Operating mode adjustment for an autonomous engine heater
Built-in keyless bypass
module settings
18
9
The built-in immobilizer key less bypass module is used to deactivate a
vehicle’s OEM immobilizer during the remote engine start
PIN code change
14
1
HCU-230/BT hood
compartment unit settings
20
10
HCU-230/BT hardware features configuration
«Diagnostic trouble codes»
reading feature settings
21
11
The built-in «DTC reading» feature configuration
Configuring hardware features
Programming is carried out according to the «Menu 1», «Menu 1.2».
Menu 1. Hardware features configuration
№
Option
Values
range
Default
values
Note
1
Vehicle model
–
–
Is setup automatically, should be adjusted manually if needed
2
Wired engine locking type
1 – 2
2
1 — Normally open (NO) relay control;
2 — Normally closed (NC) relay control
3
Engine blocking at a safe speed
1 – 3
1
1 — disabled. The engine is locked regardless of vehicle’s speed; 2- at
speed 30 km/h and slower; 3- when the vehicle is completely stopped
4
Inputs adjustment when connecting
to analog buttons
1 – 2
1
The inputs №№10, 22 (connector X1, 24-pin) are connected to:
1 — to the steering wheel (resistive) buttons;
2 — to positive and/or negative buttons (the multi-purpose
programmable inputs)
5
Ability to simultaneousely control the
OEM security system and the central
door locking
1 – 2
1
1 — enabled; 2 — disabled;
6
Sequantial CDL unlocking
1 – 2
2
Is used for controll via a phone or Key-ID tag:
1 — enabled; 2 — disabled. For control via phone
8
Vehicle’s CDL control
1 – 4
4
1 — control via a single wire (considering the CDL status);
2 — control via a single wire (regardless of CDL status);
3 — double wire control; 4 — control via CAN-bus
9
–
–
–
–
10
«Comfort» feature operation duration
1 – 6
3
1 — 10 sec;...3 — 30 sec;...6 — 60 sec.
11
Supplementary sensors type
(shock, volume)
1 – 2
1
1 — Multiplexed (for connection to multiplexed sensors);
2 — Standard (for connection to the sensors with devided «warning»
and «trigger» outputs)
12
Ability to start the engine before
carrying out authentication
1 – 2
1
1 — ON; 2 — OFF.
(The setting «2-OFF» doesn’t affect anything if only a relay
pLine-221 is used to block the engine)
13
Activation requirements for optional
PDC sensors
1 – 3
1
By shifting the gear lever to:
1 — «R» position;
2 — «D» or «R» with switching off possibility before the ride ends;
3 — «R» with switching off possibility before the ride ends
14
PDC control button
Can be used a vehicle’s button which the alarm can «sense» via
CAN-bus; vehicle’s original analog (resistive) or digital button
(positive or negative)
15
Speed monitoring for immobiliser
and AntiHiJack features
1 – 2
1
1 — ON; 2 — OFF. Affects the operating algorythm of Immobilizer and
AntiHiJack features
16
Quantity of brake pedal presses
before AntiHiJack feature is triggered
1 – 7
3
Quantity of brake pedal applications is needed to be set up in order to
determine the AntiHiJack feature operating algorithm if «Speed
monitoring for Immobilizer and AntiHiJack features» is turned
OFF or not available. The setting doesn’t affect anything if «Speed
monitoring» is ON and is available for a particular vehicle
17
GSM-engine locking
1 – 2
1
1 — ON; 2 — OFF
18
Voltage value for low-battery
warning
1 – 15
11,3
1 — 10,6 V; … 8 — 11,3 V; ... 15 — 12 V
19
Communication quality check
between the main alarm module and
the relay pLine-221
(for Prizrak 820, 840 only)
–
–
It is very necessary to check communication quality between the
main alarm module and the relay pLine-221 after the installation
20
Relay pLine built-in accelerometer
sensitivity adjustment
(for Prizrak- 820, 840 only)
1 – 4
1
1 – maximum; 2 – high; 3 – low; 4 – minimum.
Adjust sensitivity after the installation
