Svantek Shawcity SVAN 977C User Manual Download Page 70

Page: 70 / 343

SVAN 977C User Manual

or switched off. If it has happened, the first press of any key will cause the
screen to switch back on again.

Power saver delay

The power saver delay defines the delay period from the last use of any key to
the power saver mode. This delay period can be set for

Dim screen on idle

from

5 s

60 s

and for

Screen off on idle

from

1 m

60 m

. The

<ENTER>

key must be pressed for confirmation of the selection, which then also closes
the

Screen Setup

screen.

Summary of Contents for Shawcity SVAN 977C























































































































































































































































































































































Search results

Summary of Contents for Shawcity SVAN 977C

Reviews:

Related manuals for Shawcity SVAN 977C

Brands by name

Popular brands

Svantek Shawcity SVAN 977C, User Manual

Search results

Summary of Contents for Shawcity SVAN 977C

Reviews:

Related manuals for Shawcity SVAN 977C

Brands by name

Popular brands