Suzuki GN125F Service Manual Download Page 87

Page: 87 / 148

C H A S S I S

5-9

INSPECTION

DAMPER ROD RING

INNER TUBE AND OUTER TUBE

SPRING

Thread lock

Inspect the damper rod ring for wear and damage

Inspect the inner tube and outer tube sliding surface for any
scuffing or flaws.

Measure the spring free length. If it is shorter than the

service limit, replace it.

Apply Bond No 4 and Thread Lock Cement to the damper
rod bolt and tighten the bolt by using the hexagon wrench
and special tools.

Remounting the front fork in the reverse order of removal, pay
attention to the following points

：

Fork spring free length limit: 385.5 mm

* Cleaning: clean the parts with solvent and blow dry.

REMOUNTING

DAMPER ROD BOLT

O ring copper

(

)

99000-32040: Thread lock ”1303”

11F14-010: Front absorber tools

Damper rod bolt: 20~26 N•m

Do not reuse the removed O-ring.

Summary of Contents for GN125F





















































































































































Search results

Summary of Contents for GN125F

Reviews:

Related manuals for GN125F

Brands by name

Popular brands

Suzuki GN125F, Service Manual

Search results

Summary of Contents for GN125F

Reviews:

Related manuals for GN125F

Brands by name

Popular brands