Suzuki GN125F Service Manual Download Page 82

Page: 82 / 148

C H A S S I S

5-4

REASSEMBLY

Reassemble and remount the front wheel in reverse order of

removal. Pay special attention to the following points.

Apply Super Grease ”A” to bearings before reassembly.

99000-25010: Super grease ”A”

The sealed cover of the bearing must face outside.

09924-84521: Bearing installer

Left bearing

Spacer

Right bearing

Removed wheel bearing

Clearance

Install left wheel bearing

first, then install the spacer

and right wheel bearing

with the special tool and removed

wheel bearings

Apply the Super Grease A to the dust seal lips.
Install the new dust seals using the special tool.

09913-70210 : Bearing installing set (10-75 )

DUST SEAL

WHEEL BEARING

99000-25010 : Super grease ”A”

Summary of Contents for GN125F





















































































































































Search results

Summary of Contents for GN125F

Reviews:

Related manuals for GN125F

Brands by name

Popular brands

Suzuki GN125F, Service Manual

Search results

Summary of Contents for GN125F

Reviews:

Related manuals for GN125F

Brands by name

Popular brands