Suzuki GN125F Service Manual Download Page 106

Page: 106 / 148

C H A S S I S

5-28

REASSEMBLY

Reassemble and remount the rear wheel and

rear brake in

the reverse order of disassembly and removal, and also carry
out the following steps.

the

BEARING

Apply grease to the bearings before installing.

Install the bearings by using the special tool.

Insert the bearing by using the special tool.

Apply grease to the mounting drum as shown.

99000-25010: Super grease ”A”

99000-25010 Super grease ”A”

First install the bearing for right side

09913-70210 Bearing installer

REAR SPROCKET MOUNTING DRUM

09940-53311 Bearing installer

SPROCKET

Tighten the four nuts to specified torque.

Do not reuse the removed nuts, replace the nuts with
new ones for safe riding.

Sprocket lock nut: 18~28 N•m

Summary of Contents for GN125F





















































































































































Search results

Summary of Contents for GN125F

Reviews:

Related manuals for GN125F

Brands by name

Popular brands

Suzuki GN125F, Service Manual

Search results

Summary of Contents for GN125F

Reviews:

Related manuals for GN125F

Brands by name

Popular brands