Still FS-X33 Original Instructions Manual Download

Page: 57 / 94

Operation

The display and its functions

In normal truck operation, information and

error messages can be shown in the display

window (1).
Information messages describe operating er-

rors or prohibited truck statuses. Information

messages are made up of the symbol i for

information and a three or four-digit number.

If the operating error stops occurring or the

status is corrected, the information display

disappears again. In such cases, it is not usu-

ally necessary to call your service centre.
Error messages are made up of the letters

FE and a four-digit number or just a four-digit

number. The warning triangle symbol is also

shown. If error messages are displayed, call

the relevant service centre. In such cases, all

displayed error messages must be passed on.

Display and messages

Info

Reason

Remedy

i 520

If driving is selected, seat switch not active

or seat switch defective.

Sit down on the seat, have the seat switch

checked.

i 521

If lifting is selected, seat switch not active

or seat switch defective.

Sit down on the seat, have the seat switch

checked.

i 522

Seat switch was not actuated in the last 8h

or is defective

Vacate the seat and then sit down again,

have the seat switch checked.

i 523

Seat switch defective

Have the seat switch checked/changed.

i 2061

Traction controller overtemperature

Reduce the load, let the traction controller

cool down.

i 2065

Traction motor overtemperature

Reduce the load, let the motors cool down.

i 2066

Battery capacity below 20%

Charge the battery.

i 2079

Incorrect switch-on sequence

Do not press any pedals when switching

on.

i 2249

Traction controller monitoring; tempera-

ture sensor at the traction controller might

be defective

Call your service centre.

i 2253

Door switch not actuated or defective

Close the door correctly or have the switch

checked.

i 2313

Truck drives with standard parameter set

Switch on and if the error is not rectiﬁed,

call your service centre.

i 2361

Traction controller overtemperature

Reduce the load, let the traction controller

cool down.

51328042507 [EN]

Summary of Contents for FS-X33































































































Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands

Still FS-X33, Original Instructions Manual

Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands