Still FS-X33 Original Instructions Manual Download Page 35

Page: 35 / 94

Overview

Safety equipment

NOTE

There is no foot switch in trucks with a driver’s

compartment door or a closed cab.

The hydraulic functions are only enabled if:
• The seat switch and the foot switch have

been actuated.

• The desired hydraulic function is then

selected.

• The switches are all functioning correctly.
The driving function is only enabled if:
• The seat switch and the foot switch have

been actuated but the accelerator pedal

has NOT.

• The accelerator pedal is then actuated.
• The switches are all functioning correctly.
• The parking brake has been released.

NOTE

The parking brake is released as soon as the

accelerator pedal is actuated slightly.

Trucks with two accelerators pedals (dual-

pedal control)
The hydraulic functions are only enabled if:
• The seat switch has been actuated.
• The switch is functioning correctly.
The driving function is only enabled if:
• The seat switch has been actuated but the

accelerator pedals have NOT.

• One of the accelerator pedals is then

actuated.

• The switches are all functioning correctly.
• The parking brake has been released.

NOTE

The parking brake is released as soon as one

of the accelerator pedals is actuated slightly.

Monitoring

The seat switch is monitored electrically. If the

truck remains switched on for longer than 8

hours, the switch status of the seat switch must

51328042507 [EN]

Summary of Contents for FS-X33































































































Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands

Still FS-X33, Original Instructions Manual

Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands