Still FS-X33 Original Instructions Manual Download Page 53

Page: 53 / 94

Operation

Initial driving practice

Horizontal suspension*

Lever (8) can be used to switch the horizontal

suspension on and off. To do so, press the

lever in sideways and slide the seat to the

locked position. To release, press the lever

outwards.
Lever (9) can be used to adjust the rigidity of

the horizontal suspension in several stages.

To do so, move the lever to the corresponding

notch.
*option

Initial driving practice

WARNING

Before starting work, work through the Check list

before starting work,
All safety instructions must be observed.

Speeds

The driver is obliged to adjust the driving

speed to the relevant situation. Particularly

when driving around corners, the overall

height and the high centre of gravity must

be taken into consideration.

Initial driving practice

In order to become familiar with the driving

and braking characteristics of the truck, initial

driving practice should be gained on a free,

even surface in the warehouse.

51328042507 [EN]

Summary of Contents for FS-X33































































































Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands

Still FS-X33, Original Instructions Manual

Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands