Still FS-X33 Original Instructions Manual Download

Page: 83 / 94

Special equipment

Special equipment — insertion wheels for CHEP pallets

Special equipment — insertion

wheels for CHEP pallets

View of the underside of the lifting forks.
These insertion wheels (2) simplify the inser-

tion of forks into CHEP pallets. They are ﬁtted

in front of the front load wheels (1 ) towards the

fork tips.

Cold store cab

The cold store cab has following equipment

variants:
• Thermal insulation on the inside of the cab
• Double-glazed windows — heatable upon

request

• Intercom system so that the driver can

communicate with the outside world without

having to open the cab door

• Cab heating with three independent heating

modules. The interior temperature can be

adjusted via a thermostat

51328042507 [EN]

Summary of Contents for FS-X33































































































Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands

Still FS-X33, Original Instructions Manual

Search results

Summary of Contents for FS-X33

Reviews:

Related manuals for FS-X33

Brands by name

Popular brands