SRAM 2015 BOXXER TEAM Service Manual Download Page 49

Page: 49 / 53

Fork Installation

F o r k I n s t a l l a t i o n

Slide each upper tube through the lower crown. Leave enough

clearance between the upper tube and the upper crown to install

the frame bumpers. Use a 4 mm hex wrench to tighten one of the

lower crown bolts to temporarily hold the tubes in place while you

install the bumper.

Spray isopropyl alcohol or water on the inner surfaces of each

frame bumper and upper tube. Reinstall the frame bumpers onto

the upper tubes.

Push and twist the upper tubes through the upper crown until

both upper tubes extend past the top of the upper crown by an

equal amount and at least 2 mm.
Measure the distance from the top of the upper tube to the top of

the lower crown. This distance must be 156 mm (+/- 2 mm).

Align the BoXXer™ logo on the drive side upper tube with the

RockShox

logo on the lower leg.

4 mm

156 mm (+/- 2 mm)

space between frames

space between steps

space between frames

space between steps

Summary of Contents for 2015 BOXXER TEAM






















































Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands

SRAM 2015 BOXXER TEAM, Service Manual

Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands