SRAM 2015 BOXXER TEAM Service Manual Download Page 7

Page: 7 / 53

Record your Settings

R e c o r d y o u r S e t t i n g s

Use the charts below to record your BoXXer™ fork settings to return your fork to its pre-service settings. Record your service date to

track service intervals.

Service date - helps you keep track of service intervals.

Dual Crown height - measure the distance from the top of the upper to tube to the top of the

lower crown (see figure in Step 1).
Rebound setting - count the number of clicks while turning the rebound adjuster fully

counter-clockwise.
Compression setting - count the number of clicks while turning the compression adjuster fully

counter-clockwise.

S e r v i c e I n t e r v a l I n f o r m a t i o n

Maintenance

Interval (hours)

Clean dirt and debris from upper tubes

Every ride

Inspect upper tubes for scratches

Every ride

Check front suspension fasteners for proper torque

Remove lowers, clean/inspect bushings and change oil bath

Clean and lubricate coil spring assembly

100

Change oil in damping system

100

B o X X e r T o r q u e C h a r t

Part

Tool

Torque

Maxle Lite DH™ (non-drive side)

6 mm hex bit socket

8 clicks or 3.4 N

•

(30 in-lb)

Maxle Lite DH (drive side)

6 mm hex bit socket

5.7 N

•

m (50 in-lb)

Crown bolts

4 mm hex bit socket

5 N

•

m (44 in-lb)

Bottom bolts

5 mm hex bit socket

7.3 N

•

m (65 in-lb)

Top caps

24 mm socket

7.3 N

•

m (65 in-lb)

B o X X e r O i l V o l u m e

Part

Oil Weight

Volume (mL)

Drive side lower leg

0w-30

Non-drive side lower leg

Drive side upper tube

3wt

Bleed (varies)

Non-drive side upper tube

Liquid O-Ring® PM600 military grease

Summary of Contents for 2015 BOXXER TEAM






















































Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands

SRAM 2015 BOXXER TEAM, Service Manual

Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands