SRAM 2015 BOXXER TEAM Service Manual Download Page 34

Page: 34 / 53

Use the chart below to layout the shim stack for your desired tune

on your compression piston. Use a metric caliper to verify the shim

outer diameter and shim thickness or print the page at 100% scale

to arrange the shim stack using the outlines on the page.

All Charger Dampers™ in BoXXer™ ship with the Medium Damper

Tune installed.

Shim diameter

Shim thickness

0.1

Outer Dimension

(mm)

1:1* Shim Size

1:1* Shim

Thickness

(mm)

0.2

0.15

Medium CompressionTune

(Stock Tune)

Outer Dimension

(mm)

1:1* Shim Size

1:1* Shim

Thickness

(mm)

Firm CompressionTune

Outer Dimension

(mm)

1:1* Shim Size

1:1* Shim

Thickness

(mm)

0.3

Soft Compression Tune

Piston Face/Bottom of stack

0.1

0.2

0.15

18 Hoop

0.15

0.3

18 Hoop

0.1

0.3

0.2

0.15

0.1

0.15

0.3

18 Hoop

100 mm

*Print this page at 100% scale and use the

chart to layout your desired rebound tune.

Summary of Contents for 2015 BOXXER TEAM






















































Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands

SRAM 2015 BOXXER TEAM, Service Manual

Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands