SRAM 2015 BOXXER TEAM Service Manual Download Page 51

Page: 51 / 53

Fork Installation

Install the threaded end of the Maxle Lite DH™ through the drive

side of the hub until it engages the threads of the lower leg

dropout.
Use a torque wrench with a 6 mm hex bit socket to tighten the

drive side axle bolt to 5.7 N

•

m (50 in-lb).

Use a torque wrench with a 6 mm hex bit socket to tighten the

non-drive side axle bolt until you hear or feel 8 clicks or reach a

torque value of 3.4 N

•

m (30 in-lb).

Refer to your pre-service recorded settings to adjust the rebound

and compression settings on the fork.

Spray isopropyl alcohol on the entire fork and clean it with a rag.

This concludes the service for RockShox

BoXXer

™

front suspension forks.

6 mm

5.7 N•m (50 in-lb)

6 mm

8 clicks or 3.4 N•m (30 in-lb)

Summary of Contents for 2015 BOXXER TEAM






















































Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands

SRAM 2015 BOXXER TEAM, Service Manual

Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands