SRAM 2015 BOXXER TEAM Service Manual Download Page 30 | Manualshive

Page: 30 / 53

background image

30

Optional Charger Damper™ Re-tune

O p t i o n a l C h a r g e r D a m p e r ™ R e - t u n e

The Charger Damper in BoXXer™ comes with additional shims installed on the piston to allow the rider to modify the compression

and/or rebound tunes.
If your rebound setting is one or two clicks from open, we recommend changing to a soft tune on the rebound. If your compression

setting is one or two clicks from open, we recommend changing to a soft tune on the compression.
Conversely, if your rebound setting is one or two clicks from closed, we recommend changing to a firm tune on the rebound. If your

compression setting is one or two clicks from closed, we recommend changing to a firm tune on the compression.

All Charger Dampers in BoXXer ship with the Medium Damper Tune installed.

O p t i o n a l R e b o u n d R e - t u n e

Clamp the bottom of the rebound damper shaft into a RockShox

®

Rear Shock Vise Block.

N OT I C E

To prevent damage to the rebound damper shaft, do not clamp

the middle of the shaft in the vise.

Use a 10 mm socket to remove the piston nut. Use your hand to

stabilize the rebound damper shaft.

Use a small wrench or pick to slide the shims off of the rebound

damper piston. Set the shims on a rag in the order they came off

of the piston.

1

2

10 mm

Small wrench

3

«
...
28
29
30
31
32
...
»

Summary of Contents for 2015 BOXXER TEAM






















































Reviews:

No comments

Related manuals for 2015 BOXXER TEAM

Brand: CAME Pages: 4

Brand: Oh Wow Cycles Pages: 56

Brand: Yolin Pages: 25

Brand: EAL Pages: 4

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: YOELEO Pages: 3

Brand: Watts Pages: 8

Brand: HALE Pages: 44

Brand: Yakima Pages: 8

Brand: Oliver Pages: 15

Brand: daviteq Pages: 33

Brand: REV Pages: 2

Brand: Romik Pages: 6

Brand: Kensington Pages: 82

Brand: SkyBean Pages: 20

Yamaha X-MAX 300

Brand: BRUUDT Pages: 7

Brand: Hudora Pages: 12

Brand: Chillafish Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands