SRAM 2015 BOXXER TEAM Service Manual Download Page 40 | Manualshive

Page: 40 / 53

background image

40

Charger Damper™ Assembly and Bleed

Remove the cartridge tube assembly from the bicycle stand, turn

it over, and clamp the cartridge tube assembly in the bicycle stand

so the rebound shaft is oriented downward.
Pull down on the rebound shaft.

Pour RockShox® 3wt suspension fluid into the cartridge tube until

it is approximately half full.

Use the palm of your hand or a rag to cover the cartridge tube,

and cycle the damper rebound shaft a few times to help pre-bleed

air from the damper.
Pour additional RockShox 3wt suspension fluid into the cartridge

tube until the fluid is level with the top of the tube.
Use your finger to remove any air bubbles from the surface of the

fluid.

C AU T I O N - E Y E H A Z A R D

Pull the rebound damper shaft down slowly. Failure to do so

can result in fluid ejecting from the cartridge tube. Wear safety

glasses.

11

3wt

12

13

3wt

«
...
38
39
40
41
42
...
»

Summary of Contents for 2015 BOXXER TEAM






















































Reviews:

No comments

Related manuals for 2015 BOXXER TEAM

Brand: 4B Pages: 12

Brand: Panasonic Pages: 16

Brand: NEC Pages: 8

Brand: AAMP of America Pages: 6

Brand: M7 SPEED Pages: 11

McPherson Strut MIR 1G00

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 2

Brand: KEDO Pages: 2

Brand: KEDO Pages: 3

Brand: KEDO Pages: 2

DGIPOD-4655 - DATASHEET FOR IPHONE

Brand: I.SOUND Pages: 1

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

Brand: Reflecta Pages: 22

Brand: Deka Pages: 4

BIS M-411-068-001-09-S72

Brand: Balluff Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands