SRAM 2015 BOXXER TEAM Service Manual Download Page 18 | Manualshive

Page: 18 / 53

background image

18

Coil Spring Installation

C o i l S p r i n g I n s t a l l a t i o n

Install a new support washer and a new wavy washer on the spring

shaft so that the support washer is closest to the spring perch.
Install the base plate assembly onto the spring shaft so that the

small top out spring is oriented toward the spring perch.

Firmly push the spring shaft assembly into the bottom of the

upper tube until the retaining ring groove is visible.

Place the tips of large internal snap ring pliers into the eyelets of

the retaining ring and install the retaining ring into the groove.

Check that the retaining ring is properly seated in the retaining

ring groove by using the snap ring pliers to rotate the retaining

ring and seal head back and forth a few times, then firmly pull

down on the spring shaft.

Retaining rings have a sharper-edged side and a rounder-edged

side. Installing retaining rings with the sharper-edged side facing

the tool will allow for easier installation and removal.

space between frames

space between steps

1

2

3

«
...
16
17
18
19
20
...
»

Summary of Contents for 2015 BOXXER TEAM






















































Reviews:

No comments

Related manuals for 2015 BOXXER TEAM

Brand: Hamax Pages: 74

Brand: Acclima Pages: 16

Brand: Access One Pages: 2

Brand: Accelleran Pages: 19

Brand: E-max Pages: 4

Brand: Hanlong Pages: 26

Brand: i-onik Pages: 6

Brand: FABRICBIKE Pages: 20

Brand: Oki Pages: 2

Brand: Oki Pages: 20

Brand: Oki Pages: 2

SmartSensor Matrix

Brand: Wavetronix Pages: 2

Brand: Watt Stopper Pages: 8

Brand: Yamaha Pages: 33

Brand: Yamaha Pages: 17

Brand: Uebler Pages: 18

Brand: NeuLog Pages: 4

Brand: Qwic Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands