SRAM 2015 BOXXER TEAM Service Manual Download Page 14 | Manualshive

Page: 14 / 53

background image

14

Lower Leg Seal Service

Hold the lower leg firmly and use the seal installation tool to push

the lower oil seal evenly into the leg until the bottom surface of

the seal is flush with the bottom of the seal pocket.

Remove the wire spring from the new dust wiper seal and set the

spring aside.
Insert the narrow end of the new dust wiper seal into the recessed

end of the 35 mm seal installation tool.

Hold the lower leg firmly and use the seal installation tool to push

the dust wiper seal evenly into the lower leg until the seal surface

is flush with the top of the lower leg surface.
Reinstall the wire spring onto the dust wiper seal.
Repeat on the other side.

5

35 mm seal installation tool

35 mm seal installation tool

6

7

35 mm seal installation tool

«
...
12
13
14
15
16
...
»

Summary of Contents for 2015 BOXXER TEAM






















































Reviews:

No comments

Related manuals for 2015 BOXXER TEAM

Brand: Voxx Pages: 7

Brand: Daga Pages: 28

Brand: Makita Pages: 20

Brand: E-Mu Pages: 52

Brand: 2easy Pages: 17

Brand: 2DI Pages: 38

Brand: 2DI Pages: 3

Brand: Dancover Pages: 31

Brand: Lanier Pages: 3

HighLine ABF0166

Brand: Mactronic Pages: 2

Brand: Allen Sports Pages: 2

Fireplace Surrounds None

Brand: Dimplex Pages: 2

Brand: Gira Pages: 10

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

WirelessAIR 73000EZ

Brand: Air Lift Pages: 12

Brand: ergobaby Pages: 8

INV 220V Series

Brand: Sunny Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands