SRAM 2015 BOXXER TEAM Service Manual Download Page 43 | Manualshive

Page: 43 / 53

background image

43

Charger Damper™ Assembly and Bleed

Fill the bleed syringe 1/3 full with 3wt suspension fluid and thread

the syringe into the compression top cap assembly.

Create a vacuum in the damper assembly by pulling up on the

syringe handle and simultaneously pushing up on the rebound

damper shaft. This will force bubbles out of the damper assembly.
Pressurize the damper assembly by pushing down on the syringe

handle and simultaneously pulling down on the rebound damper

shaft.
Continue to hold down on the syringe handle and simultaneously

cycle the rebound damper shaft a few times to purge bubbles.

The bladder will expand and contract. This is normal.

Repeat pulling a vacuum and pressurizing the damper assembly

until only very small bubbles emerge from the damper assembly.

21

3wt

22

«
...
41
42
43
44
45
...
»

Summary of Contents for 2015 BOXXER TEAM






















































Reviews:

No comments

Related manuals for 2015 BOXXER TEAM

Brand: DAPU Pages: 4

Brand: NAKTO Pages: 29

Brand: Data Aire Pages: 82

Brand: UNIT 1 Pages: 23

Brand: Kabuto Pages: 16

Brand: Parker Pages: 2

Brand: Park Tool Pages: 2

Brand: ParaZero Pages: 17

XMODS Custom RC

Brand: Radio Shack Pages: 4

Brand: Imax Pages: 3

Brand: Jackco Pages: 11

Brand: Pout Pages: 5

Brand: Subaru Pages: 3

Brand: Prorack Pages: 15

Brand: PROAIM Pages: 3

PSEN sg2c-5CCLLE

Brand: Pilz Pages: 52

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: Smith-Victor Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands