SRAM 2015 BOXXER TEAM Service Manual Download | Manualshive

Page: 13 / 53

background image

13

Lower Leg Seal Service

L o w e r L e g S e a l S e r v i c e

Place a rag on top of the dust wiper seal. Insert the tip of a

downhill tire lever underneath the lower lip of the lower black oil

seal located above the upper bushing.

N OT I C E

If using a flat head screwdriver, make sure it has a round shaft. A

screwdriver with a square shaft will damage the lower leg.

Stabilize the lower leg on a bench top or on the floor. Press down

on the downhill tire lever handle to remove both seals at the same

time. Repeat on the other side.

N OT I C E

Keep the lower leg assembly stable. Do not allow the lower leg to

twist in opposite directions, compress toward each other, or be

pulled apart. This will damage the lower leg.

Spray isopropyl alcohol on the inside and outside of the lower leg

and clean it with a rag.
Wrap a rag around a long dowel and insert it into each lower leg to

clean the inside.

Position the new lower oil seal, with the grooved side visible, onto

the stepped side of a 35 mm seal installation tool.

1

Downhill tire lever

2

3

35 mm seal installation tool

4

«
...
11
12
13
14
15
...
»

Summary of Contents for 2015 BOXXER TEAM






















































Reviews:

No comments

Related manuals for 2015 BOXXER TEAM

Brand: D-2 Incorporated Pages: 28

Brand: D+H Pages: 12

Brand: Labelmate Pages: 2

Brand: BAFANG Pages: 4

Brand: QIMMIQ Pages: 16

Brand: QA1 Pages: 10

HighLine ABF0166

Brand: Mactronic Pages: 2

Brand: media-tech Pages: 13

Brand: matev Pages: 23

Centronic VarioControl VC280

Brand: Becker Pages: 20

1501-3120-6010-100

Brand: S+S Regeltechnik Pages: 16

Brand: echoflex Pages: 8

Brand: Bicycles4u Pages: 8

Brand: Saab Pages: 3

Brand: R&G Pages: 8

Brand: Profoto Pages: 12

Honeywell RE210P

Brand: Resolution Pages: 4

Yamaha X-MAX 300

Brand: BRUUDT Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands