SRAM 2015 BOXXER TEAM Service Manual Download Page 9

Page: 9 / 53

Fork Removal

Use a 4 mm hex wrench to loosen the four lower crown and two

upper crown pinch bolts clamping the upper tubes.

Do not loosen the steerer tube clamping bolt located on the

upper crown.

Slide the upper tubes down so they clear the upper crown. Leave

enough clearance between the upper tube and upper crown to

remove the frame bumpers.
Use a 4 mm hex wrench to tighten one of the lower crown bolts

to temporarily hold the tubes in place while you remove the frame

bumpers.

Use your thumb to pry the thickest section of each frame bumper

away from the upper tube. Spray isopropyl alcohol or water

between each bumper and upper tube. Twist the frame bumpers

back and forth until they are loose on the upper tubes.
Remove the frame bumpers from the upper tubes.

Use a 4 mm hex wrench to loosen the lower crown bolt. Slide

the tubes through the lower crown and remove the fork from the

bicycle.
Spray isopropyl alcohol on the upper tubes and crown clamping

surface and clean them with a rag.

4 mm

Lower crown

4 mm

Upper crown

4 mm

Summary of Contents for 2015 BOXXER TEAM






















































Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands

SRAM 2015 BOXXER TEAM, Service Manual

Search results

Summary of Contents for 2015 BOXXER TEAM

Reviews:

Related manuals for 2015 BOXXER TEAM

Brands by name

Popular brands