Spectra Watermakers Catalina 340 Z Installation And Operating Manual Download Page 60 | Manualshive

Page: 60 / 90

background image

60

Technical Bulletins

The following pages include Spectra’s most commonly-used technical bulletins, covering tests,
adjustments, troubleshooting, and common points of confusion. Many more technical bulle-
tins are available on the Spectra website, www.spectrawatermakers.com.

ACCUMULATOR PRESSURE

Your Catalina 340 Z is supplied with a pressure accumulator tank (PL-ACC-TK) installed in the
feed water line between the feed pump and the Clark Pump.

The purpose of the feed line accumulator is to reduce the spikes in the feed pressure caused
by the cycling of the Clark Pump. If the accumulator is not properly charged it can lead to pres-
sure spikes and system shut down. The accumulator has a Schrader air valve, like a car tire,
which allows the internal air bladder of the accumulator to be pre-charged. The accumulator
should be pumped up to about 60 psi (4.1 bar) for best results. Add air using a tire pump or air
compressor. You can experiment with the exact pressure that will give the best pulsation
dampening on your installation.

Schrader valve

«
...
58
59
60
61
62
...
»

Summary of Contents for Catalina 340 Z



























































































Reviews:

No comments

Related manuals for Catalina 340 Z

Brand: Hoshizaki Pages: 2

Brand: Battery Watering Technologies Pages: 2

Brand: EcoFast Pages: 7

Brand: Rainfresh Pages: 9

Scalekleen EV9796-01

Brand: Everpure Pages: 2

Brand: Toro Pages: 6

Brand: purway Crystal Group Pages: 5

FiltoClear 20000

Brand: Oase Pages: 212

Brand: Nilfisk-Advance Pages: 84

Brand: NEXT pool Pages: 35

Brand: Armstrong Pages: 2

HydroTap G4 802701

Brand: Zip Pages: 24

Brand: Enviro Pages: 20

Brand: SpectraPure Pages: 8

Brand: Lincoln Pages: 24

Brand: Lincoln Pages: 38

Brand: Viking Pages: 13

FIRE–BALL 300 Air Motor Muffler Kit

Brand: Graco Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands