background image

STANDARD RESPONSE 

ELO UPRIGHT SPRINKLER

VK530 

(STORAGE-DENSITY/AREA)

TECHNICAL DATA

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: [email protected]

Visit the Viking website for the latest edition of this technical data page.

Form No. F_010692    21.09.16     Rev 21.1

Page 1 of 5

1.  DESCRIPTION

The Viking Standard Response ELO Upright Sprinkler VK530 is a thermosensitive 

glass bulb spray sprinkler available in several different finishes and temperature 

ratings to meet design requirements. The special Polyester, PTFE, and Electroless 

Nickel PTFE (ENT) coatings can be used in decorative applications where colors 

are desired. In addition, these coatings have been investigated for installation 

in corrosive environments and are listed/approved as indicated in the Approval 

Charts. 
The extra-large orifice provides greater flows at lower pressures than standard 

orifice  or large orifice sprinklers. This feature allows reduced pipe sizing for 

hydraulically calculated sprinkler systems, which require high densities of water. 

On existing systems, replacing large orifice sprinklers with extra-large orifice 

sprinklers may provide the higher densities required to allow an increase in the 

hazard classification of an occupancy.
Viking standard response sprinklers may be ordered and/or used as open sprin-

klers (glass bulb and pip cap assembly removed) on deluge systems. Refer to 

Ordering Instructions 

below. 

2.  LISTINGS AND APPROVALS

cULus Listed: 

Category VNIV

FM Approved:

 Class 2009

Refer to Approval Chart 1 and Design Criteria on page 3 for cULus Listing requir-

ments, and refer to Approval Chart 2 and Design Criteria on page 4 for FM Approval requirements that must be followed.

3.  TECHNICAL DATA

Specifications:

Available since 1992.

Maximum Working Pressure: 175 psi (12 bar). 

Factory tested hydrostatically to 500 psi (34.5 bar).

Thread size: 3/4” NPT or 20 mm BSP 

Nominal K-Factor: 11.2 U.S. (161.3 metric

*

)

*Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0.

Glass-bulb fluid temperature rated to -65 °F (-55 °C)

Overall Length: 2-5/16” (58.7 mm)

Material Standards:

Sprinkler Frame: Brass UNS-C84400

Deflector: Brass UNS-C51000

Bulb: Glass, nominal 5 mm diameter

Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel UNS-S30400

Compression Screw: Brass UNS-C36000

Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape

For PTFE Coated Sprinklers:

 

Belleville Spring-Exposed, Screw-Nickel Plated, Pip Cap-PTFE Coated

For Polyester Coated Sprinklers:

 

Belleville Spring-Exposed

For ENT Coated Sprinklers: Belleville Spring-Exposed, Screw and Pipcap-ENT plated

Replaces Form No. F_010692 Rev 19.1 

(Updated Deflector Material)

NOTE: As of May 2018 all logos have been removed from the 

wrench boss.

Summary of Contents for VK530














Reviews: