Spectra Watermakers Catalina 340 Z Installation And Operating Manual Download Page 39 | Manualshive

Page: 39 / 90

background image

39

To access this information about your watermaker while it is running press the Alarm Dis-
play button (bottom right). This will allow you to scroll through the product flow, salinity,
feed water pressure, and pre-filter condition screens.

Product Flow
13-15 GPH (49—57LPH)

NOTE: To switch from Imperial (gallons) and
Metric Units (Liters) see page 74, Programming
from the Display.

Salinity
Salinity reads in PPM, parts per million, and
controls the diversion valve. If the salinity is
higher than 750ppm, the red REJECT LED is
illuminated and the product water is sent
overboard. If the salinity is less than 750
PPM, the green GOOD LED is illuminated,
and the product water is sent to the tank.

Feedwater Pressure
Pressure range 90-100 PSI (6.2–7 BAR)

Pressure will be higher in cold water and lower
in warm water. Extreme salinity or temperature
conditions may result in operating pressures
outside of the nominal range.

Pre-filter Condition
PREFILTER warns that filters are getting dirty,
and they should be changed as soon as conven-
ient. If the graph reaches full scale the machine
will alarm Service Prefilters and shut off.

The MPC 5000 board is fully programmable from the remote display. Instructions on
how to access and adjust the operating parameters are on page 74 of this manual.

Nominal Operating Parameters

«
...
37
38
39
40
41
...
»

Summary of Contents for Catalina 340 Z



























































































Reviews:

No comments

Related manuals for Catalina 340 Z

Brand: Kärcher Pages: 60

FiltraClear 2500 PlusSet

Brand: ubbink Pages: 29

BioTec ScreenMatic 2

Brand: Oase Pages: 68

Brand: Ispring Pages: 12

Brand: SANUSLIFE Pages: 5

Filtral 3000 UVC

Brand: Oase Pages: 20

Brand: MSW Pages: 43

Brand: Bluewater Pages: 9

Brand: 3M Pages: 2

Dual Manifold Water Filtration Systems

Brand: 3M Pages: 12

Brand: Parker Pages: 12

Brand: Parker Pages: 21

Brand: Parker Pages: 26

Proceptor GMC 100

Brand: ZURN Pages: 36

Brand: Potable Aqua Pages: 12

Brand: Fiskars Pages: 21

Brand: Patching Panda Pages: 3

Brand: SPEL Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands