manualshive.com logo in svg

Spectra Watermakers Catalina 340 Z, Installation And Operating Manual

The Spectra Watermakers Catalina 340 Z is a high-quality water purification system designed with efficiency and reliability in mind. To ensure hassle-free installation and operation, make sure to download the comprehensive Installation And Operating Manual for free from manualshive.com. Discover the true potential of this exceptional product today!

Share
Download
background image

 7 

 

Operation 

Table of Contents 

 
Installation

 ................................................................................................................. 11 

Getting Started .............................................................................................................. 13 
Introduction .................................................................................................................. 14 
Installation Basics .......................................................................................................... 17 
Catalina Plumbing Schematic ......................................................................................... 18 
Product Water plumbing ............................................................................................... 21 
Tube Fitting Assembly Procedures ................................................................................. 22 
Wiring ........................................................................................................................... 24 
Remote Display Installation ........................................................................................... 26 
MPC Tank Switch Wiring and Operation ........................................................................ 27 
Z-Ion and Z-Brane Membrane Protection Systems………………………………………………………..29 
Z-Ion Installation…………………………………………………………………………………………………………..30 
Z-Ion Testing………………………………………………………………………………………………………………...32 
Z Brane Installation ........................................................................................................ 33 
 

Operation

 ................................................................................................................... 37

 

New Systems Start Up and Testing ................................................................................ 39 
Nominal Operating Parameters ..................................................................................... 41 
Dry Testing with an Artificial Ocean ............................................................................... 42 
Normal Operation and Fresh Water Flush...................................................................... 43 
Auto Store and Flush Cycle Adjustment ......................................................................... 44 
Alarm Override and Manual Operation .......................................................................... 45 
 

Maintenance, Storage, and Troubleshooting

..................................................... 47

 

Suggested Spares........................................................................................................... 49 
Maintenance ................................................................................................................. 50 
Introduction to Spectra Chemicals ................................................................................. 52 
Long Term Storage Procedures ...................................................................................... 54 
Winterizing with Propylene Glycol ................................................................................. 55 
Membrane Cleaning Procedure ..................................................................................... 56 
Troubleshooting ............................................................................................................ 57 
Poor Water Quality ........................................................................................................ 59 
Catalina Flow Test ......................................................................................................... 60 
Technical Bulletins ......................................................................................................... 62 
 

Summary of Contents for Catalina 340 Z



























































































Reviews:

No comments

Related manuals for Catalina 340 Z

SimPure 100GPD T1-6-100G Owner'S Manual preview
100GPD T1-6-100G
Brand: SimPure Pages: 18
Toray HSU-1515 Instruction Manual preview
HSU-1515
Brand: Toray Pages: 45
Westfalia 87 37 91 Instruction Manual preview
87 37 91
Brand: Westfalia Pages: 4
Vortex RH9521-12 Installation Manual preview
RH9521-12
Brand: Vortex Pages: 7
MTI AUTOFRY OFS Operator'S Manual preview
AUTOFRY OFS
Brand: MTI Pages: 16
Clean Water Systems 7500-REV4 Installation Manual preview
7500-REV4
Brand: Clean Water Systems Pages: 17
SNOWJOE AquaJoe AJ-OMS20-BRS-RM Manual preview
AquaJoe AJ-OMS20-BRS-RM
Brand: SNOWJOE Pages: 8
Ozone RAINSAFE Installation, Operation & Maintenance Manual preview
RAINSAFE
Brand: Ozone Pages: 2
Expondo UNI_WATER_05 User Manual preview
UNI_WATER_05
Brand: Expondo Pages: 11
WALPOL WNG-S1 Installation And Operating Instructions Manual preview
WNG-S1
Brand: WALPOL Pages: 24
Parker Hiross Hypersep Series User Manual preview
Hypersep Series
Brand: Parker Hiross Pages: 20
Aquablu Pro Manual preview
Pro
Brand: Aquablu Pages: 40
Val-Tex Easy Lube 40-70 Operating Manual preview
Easy Lube 40-70
Brand: Val-Tex Pages: 41
Better Water 1232 RO Operator'S Manual preview
1232 RO
Brand: Better Water Pages: 82
Tyent Rettin UCE Series User Manual preview
Rettin UCE Series
Brand: Tyent Pages: 28
LIFE Ionizer M9 X User Manual preview
M9 X
Brand: LIFE Ionizer Pages: 56
SteriPEN Sidewinder User Manual preview
Sidewinder
Brand: SteriPEN Pages: 4
IDEAL H2O 738300 Setup And Maintenance Manual preview
738300
Brand: IDEAL H2O Pages: 12

Brands by name

Popular brands

Load more brands