Spectra Watermakers Catalina 340 Z Installation And Operating Manual Download Page 63 | Manualshive

Page: 63 / 90

background image

63

Performing a Fresh Water Flush with a Failed Salinity Probe

In the event of a “Salinity Probe Failed” alarm on the remote display the alarm function can be
defeated to allow the system to remain in the Auto Store mode until repairs can be facilitated.
Access the program mode, as outlined on page 74, Programming from the Display. Scroll
through the menus until you reach the Disable Salinity heading. Press the Auto Store button
once, this will change the setting from NO to YES. Wait 40 seconds for the display to timeout
and return to the default screen. Press Auto Store once. The system will begin Auto Store
Mode, flushing itself and then initiating the flush interval timer as outlined on page 44.

Performing a Fresh Water Flush with a Failed Inlet Pressure Transducer

In the event of a “Service Prefilter” alarm on the remote display that cannot be cleared by re-
placing the pre-filters, the alarm function can be defeated to allow the system to remain in
the Auto Store mode until repairs can be facilitated. Access the Program Mode, as outlined on
page 74, Programming from the Display. Scroll through the menus until you reach the Disable
Prefilter heading. Press the Auto Store button once, this will change the setting from NO to
YES. Wait 40 seconds for the display to timeout and return to the default screen. Press Auto
Store once. The system will begin Auto Store Mode, flushing itself and then initiating the flush
interval timer as outlined on page 44.

«
...
61
62
63
64
65
...
»

Summary of Contents for Catalina 340 Z



























































































Reviews:

No comments

Related manuals for Catalina 340 Z

Brand: Water Factory Systems Pages: 15

ProfiClear Premium L

Brand: Oase Pages: 398

Brand: WaterTech Pages: 12

Brand: PurePro Pages: 4

Brand: Envirovent Pages: 16

Brand: Hunter Pages: 2

NANOpure DIamond D11931

Brand: Barnstead|Thermolyne Pages: 56

Brand: SPX Pages: 36

Brand: GE Pages: 84

Brand: Zodiac Pages: 60

Brand: Laica Pages: 3

Brand: Bluewater Pages: 92

DW03500 pureFlow

Brand: Siemens Pages: 202

Brand: Unimec Pages: 32

Brand: Vizion Pages: 16

Brand: SWT Pages: 12

Brand: Filtration Group Pages: 52

Brand: AQUAJOE Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands