Spectra Watermakers Catalina 340 Z Installation And Operating Manual Download Page 15 | Manualshive

Page: 15 / 90

background image

15

Feed Pump Module: Mount the feed pump module on a
vertical surface, which can be up to 3feet (1.0M) above the
waterline. It is preferable to mount as low as possible. Lo-
cate in an area that allows easy access to the filter housing
and the left side of the enclosure. Place where water spills
during filter changes will not be a problem, and keep future
maintenance in mind. The feed pump has overheat protec-
tion and will not operate properly at ambient temperatures
over 120F (48C).

Note: When plumbing the Catalina feed pump module, route the feed water hose so that the
front cover may be opened without removing the hose or tubing. All tubing connections are made
using John Guest connectors, shown on page 22. After assembling all plumbing fittings, thorough-
ly check for leaks.

Feed Pressure Sensor
(red) measures pressure
after the feed pump.

Boost pump voltage
booster.

Motor Speed Controller

Introduction to Components continued...

Absolute Pressure
Sensor (yellow)
measures boost pump
pressure.

MPC Control Box

Auto/Manual/Service
Toggle Switch

Pump
Motor

Mag Drive
Pump

Pre-filter

Loosen the thumb screws and fold out the front cov-
er of the feed pump module for access:

«
...
13
14
15
16
17
...
»

Summary of Contents for Catalina 340 Z



























































































Reviews:

No comments

Related manuals for Catalina 340 Z

Brand: AmeriWater Pages: 16

Brand: NatureWater Pages: 5

Brand: Waldbeck Pages: 72

Brand: Clack Valves Pages: 26

Brand: Jandy Pages: 72

Brand: Duro Pages: 42

Brand: Hydro Action Pages: 60

Brand: EasyPro Pages: 3

Brand: Unimec Pages: 32

Brand: Finerfilters Pages: 18

AQUAJOE AJ-OSPR20

Brand: SNOWJOE Pages: 16

Brand: ATS Pages: 23

MICROMATIC VK134

Brand: Viking Pages: 4

Micromatic VK100

Brand: Viking Pages: 6

Brand: Viking Pages: 3

Brand: Culligan Pages: 4

AQUA-CLEER BXL Series

Brand: Culligan Pages: 7

Spindl-Gard 24B219

Brand: Graco Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands