Sound Devices 702T User Manual Download Page 35 | Manualshive

Page: 35 / 84

Sound Devices 702T User Manual Download Page 35

702T User Guide and Technical Information

33

Things to consider when using Time Code Hold Off:

• This feature only applies in

EXT TC - AUTO RECORD

and

EXT TC/ CONT - AUTO RECORD

.

• If Pre-Roll is set, it will be applied. Pre-Roll will only capture audio from the initial detection of

a time code signal. If no Pre-Roll is selected, the file will begin after the Hold Off time expires.

It is best practice to set Pre-Roll, in the Setup Menu option

REC: PRE-ROLL TIME

, to a value

greater than the selected Hold Off value. This ensures that audio is captured from the moment

a time code signal is detected and unintentional files triggered by short bursts of time code are

not generated.

Jam Menu

Time code setup is done from the jam menu selection,

TIMECODE JAM MENU

. Pressing and holding the

drive button then the

menu button enters the jam menu. In this menu, the top of the display

shows the value of signal present on the time code input and the bottom of the display shows the

currently set time code value. In addition, the 702T displays the frame rate of the incoming time code

and the current frame rate setting of the 702T.

current 702T timecode/u-bit value

menu

selection

external time code/u-bit value received by 702T

press to jam

The 702T time code generator can be set in three ways.

Jam RX TC

When the JAM RX TC menu item is highlighted in the jam menu, the external time code, user bits,

and frame rate are shown at the top of the LCD screen; the 702T internal generator, user bits, and

frame rate are shown at the bottom of the screen. To jam the 702T from an external value, press soft

button next to the jam button or the Rotary Switch button. The screen will display

JAMMING

. Once

the 702T is jammed to the external time code, the external and internal numbers will match and run

in sync.

no valid time code is connected

Make certain that the external time code source appears in the time code jam menu. If the 702T does

not receive valid time code from the sending source the jam menu displays lines in place of numbers.

Identical to the Ambient Recording series of time code products, the 702T time code generator can “cross
jam” select frame rates. The 702T will cross jam time code at the top of the second for phase-accurate (the
00 frames will match) time code at the set frame rate.

Jam Zeros

This menu selection resets the internal generator to zero.

«
...
33
34
35
36
37
...
»

Summary of Contents for 702T





















































































Reviews:

No comments