Sorvall WX 100 Ultra Instruction Manual Download Page 87

Page: 87 / 131

Operation

Features of the menu screen

Thermo Scientific

WX Ultra Series

2-71

User list

The Centrifuge User List screen is displayed. This screen allows you to register, change, and delete any
ID code and user name.

Use cursor keys to move the cursor to
reservation No. you want to delete. (In
this example, No. 3 is selected.)

Enter the ID Code of the reserving per-
son proper. (4-digit number)

Select “Delete”.

Select “Yes”.

• The ID Code input field is

displayed in the message
field in the bottom row.

ID code

• When the ID Code is

accepted, the reserve/delete
selection message is
displayed in the message
field of the bottom row.

• The confirmation message is

displayed in the bottom row.

• The No.3 reservation display

disappears from the
centrifuge reservation list
and the reservation delete
completion message is
displayed in the bottom row.

Summary of Contents for WX 100 Ultra




































































































































Search results

Summary of Contents for WX 100 Ultra

Reviews:

Sorvall WX 100 Ultra, Instruction Manual, Page: 87 / 131

Search results

Summary of Contents for WX 100 Ultra

Reviews: