manualshive.com logo in svg

Sorvall WX 100 Ultra, Instruction Manual, Page: 119 / 131

Share
Download
Sorvall WX 100 Ultra Instruction Manual Download Page 119

Service Decontamination Policy

A-2

WX Ultra Series

Thermo Scientific

be borne by the sender. Decontamination Information Certificates are included with these 
instructions. Additional certificates are available from the local Account Representative or Field 
Service Engineer. In the event these certificates are not available, a written statement certifying that 
the unit has been properly decontaminated and outlining the procedures used will be acceptable. 

WEEE Compliance

This product is required to comply with the European Union’s Waste Electrical & Electronic 
Equipment (WEEE) Directive 2002/96/EC. It is marked with the following symbol:

Thermo Electron has contracted with one or more recycling/disposal companies in each EU Member 
State, and this product should be disposed of or recycled through them. Further information on 
Thermo Electron`s compliance with these Directives, the recyclers in your country, and information 
on Thermo Electron products which may assist the detection of substances subject to the RoHS 
Directive are available at 

www.thermo.com/WEEERoHS

Note  

The Field Service Engineer will note on the Customer Service Repair Report if 

decontamination was required and, if so, what the contaminant was and what procedure was 
used. If no decontamination was required, it will be so stated.

Summary of Contents for WX 100 Ultra




































































































































Reviews:

No comments