Sorvall WX 100 Ultra Instruction Manual Download Page 54 | Manualshive

Page: 54 / 131

Sorvall WX 100 Ultra Instruction Manual Download Page 54

Operation

How to use the FUNCTION field

2-38

WX Ultra Series

Thermo Scientific

1. Step display

The PROGRAM field displays steps as follows:

When the system finishes separating step 1 and moves to step 2,

When the system moves from step 2 to the final step 3,

Thus, you can see at a glance how many steps are stored in the specified memory and which step the
centrifuge is following.

2. While the instrument is running (while the rotor is spinning), you cannot store a stepmode run

condition. Always perform this function while not in running.

3. To check the contents (run conditions) of a step-mode program memory number, follow processes

1 through 3. To get back to the Run Screen after the check, press ESC key.

4. To perform a combination of a step mode run with an RTC (real-time control) run (see Section

RTC (real-time control) feature

), call a program memory number, then set RTC.

The system then calculates the total of running times of all steps of the programmed run and
calculates the startup time for RTC. You therefore cannot call a program memory number after
setting RTC.

14

To run the centrifuge, select Yes.

Yes

No

>> If you select “Yes”:

>> The message field in the bottom row displays PROG.

>> If you select “No”, the message field in the bottom row displays what
you see in process 10. Make the selection again.

15

Start running the centrifuge under nor-
mal operation with no changes made
to the operational conditions.

>> Run the centrifuge according to

Normal operation

.

>> If you make changes to the run conditions (such as SPEED and TIME) after call-
ing a program, the program you have just called gets canceled. You must call the
program again.
>> Pressing START makes the rotor rotate under the run condition of step 1.
>> When step 1 ends, the system moves to steps 2 and 3 automatically.

•

The display switches back to the
Run Screen.

• The run conditions of step 1 in

memory appear in the respective
fields.

In the Run Screen, the run
conditions of this step are
displayed (step 1 in this case).

Final step

«
...
52
53
54
55
56
...
»

Summary of Contents for WX 100 Ultra




































































































































Reviews:

No comments