manualshive.com logo in svg

Sorvall WX 100 Ultra, Instruction Manual, Page: 83 / 131

Share
Download
Sorvall WX 100 Ultra Instruction Manual Download Page 83

 Operation

When power failure occurs

Thermo Scientific

WX Ultra Series

2-67

Figure 2-16 

Removing the front cover

(4) Open the air vent (by turning the vacuum release screw on the left of the vacuum chamber 
counterclockwise) to let air into the rotor chamber. When the pressure in the rotor chamber reaches 
atmospheric pressure, do not forget to tighten the vacuum release screw as it was before. (See Fig. 
2-16.)

(5) Pull the door unlock wire on the right of the vacuum chamber and, at the same time, push the door 
handle. Then the door opens. When opening the door, confirm that the rotor is not rotating. If it is 
still rotating, immediately close the door.

(6) Remove the rotor. After the removal, close the air vent and put the front cover back to the 
ultracentrifuge. Insert the top surface of the front cover in the bottom surface of the front side of the 
table and put the bottom surface of the front cover on the support plate of the front cover by reversing 
the removing procedure. Attach it on the frame with four M5 hexagon head bolts.

Table

Front cover

Cabinet cover

M5 hexagon head 
bolt for fixing the 
front cover (4 pcs.)

WARNING

Never touch the rotor while it is rotating.

Summary of Contents for WX 100 Ultra




































































































































Reviews:

No comments