Sorvall WX 100 Ultra Instruction Manual Download Page 51

Page: 51 / 131

Operation

How to use the FUNCTION field

Thermo Scientific

WX Ultra Series

2-35

Select “Creating or Changing.”

Enter a desired condition.

To select SPEED, press

To select no rotor, press.

>> To select and enter RCF

max

or RCF

avg

, see Section

1. Programming procedure for

run conditions (creating or changing)

Specify run conditions for step 1.

>> If you press the cursor key

(downward) after setting numeric value for

DECEL (D) in step 1, setting the run conditions in step 1 finishes and step 2 enters
into an input wait state.

Then specify run conditions for step 2.

• The message field in the bottom

row switches to what you see on
your left-hand side.

• The display switches to the

Choose Rotor screen.

• The display switches to the

SPEED priority setting field and
the SPEED area blinks.

Downward cursor key

• The entry of run conditions for

step 1 is complete.

Downward cursor key

• The entry of run conditions for

step 2 is complete.

Summary of Contents for WX 100 Ultra




































































































































Search results

Summary of Contents for WX 100 Ultra

Reviews:

Sorvall WX 100 Ultra, Instruction Manual, Page: 51 / 131

Search results

Summary of Contents for WX 100 Ultra

Reviews: