manualshive.com logo in svg

Sorvall WX 100 Ultra, Instruction Manual, Page: 27 / 131

Share
Download
Sorvall WX 100 Ultra Instruction Manual Download Page 27

 Operation

Basic operating procedure

Thermo Scientific

WX Ultra Series

2-11

Basic operating procedure

There are two basic modes of operation, normal and zonal. The procedures for these two modes are shown in Fig. 2-5.

START

Turn on the POWER.

Open the chamber door and 

install the rotor.

Normal run

Close the door and set the run 
conditions.

Press VACUUM.

For information on how to set 
the run conditions, see 
Section 

Basic operation

Vacuum pump is ON.

 

Temperature control starts. 
Check the set run conditions 
for accuracy.

Press START.

Rotor accelerates to the set speed, and then 

high-speed centrifugation begins.

: Indicates panel key.

Zonal run

Reaches the set time, 

or press STOP.

Rotor comes to a stop.

Press VACUUM.

Temperature control is OFF. 
Vacuum pump is OFF. 
Air valve is open and door lock 
is released.

Remove the rotor and turn off 

the POWER switch.

END

Summary of Contents for WX 100 Ultra




































































































































Reviews:

No comments