manualshive.com logo in svg

Sony StorStation LIB-81, Operating Instructions Manual, Page: 5 / 102

Share
Download
Sony StorStation LIB-81 Operating Instructions Manual Download Page 5

5

Basic Settings............................................................43

Disabling the Life Warning Display ............................. 43
Setting the Bar Code ..................................................... 44
Setting the R-MIC Function.......................................... 44
Adjusting the Brightness of the LCD Panel.................. 45
Using the Sequential Mode ........................................... 46

Disabling the Buttons on the Front Panel ...............47
Assigned Element Addresses ..................................48
Handling the Cartridges ............................................48

Handling........................................................................ 48
Storing ........................................................................... 49

Daily Maintenance .....................................................49

Chapter 4   Operating the AIT Library

Overview.....................................................................50
Using the Cartridges .................................................50

Taking Out the Cartridges............................................. 50
Replacing the Cartridges ............................................... 53
Moving the Cartridges .................................................. 59

Viewing Information Related to the AIT Library .....59
Viewing Cartridge Information .................................60

Chapter 5   Operating the AIT Drive

Overview.....................................................................62
Viewing Information Related to the AIT Drive.........62
Cleaning the AIT Drive ..............................................63

Chapter 6   Using the Library Administration Menu

Overview.....................................................................66
Library Administration Menu....................................67
Accessing Library Administration Menu.................67
Menu Items.................................................................69
System Configuration Menu .....................................69

Configuration ................................................................ 70
Network......................................................................... 71
SCSI ID ......................................................................... 74
Password ....................................................................... 75

Maintenance Menu ....................................................76

Life Count ..................................................................... 77
Error Count ................................................................... 78
Sensor............................................................................ 79
History........................................................................... 81
Diagnostic ..................................................................... 82
Firmware Upload .......................................................... 83

Summary of Contents for StorStation LIB-81







































































































Reviews:

No comments