Sony StorStation LIB-81 Operating Instructions Manual Download Page 11 | Manualshive

Page: 11 / 102

background image

11

Chapter 1 Introduction

Operating systems:
- Microsoft Windows 95, Microsoft Windows 98, Microsoft Windows Me,

and Microsoft Windows 2000

Browsers:
- Microsoft Internet Explorer 5.01 or later
- Netscape Communicator 4.7 or later

Compatible Data Cartridges

This section describes data cartridges used in the AIT library.

AIT Cartridges

AIT cartridges for use with your built-in AIT drive can be used in the AIT
library. To achieve the maximum transfer rate and recording capacity, use the
optimum cartridges for your type of AIT drive. For information on recording
capacities, refer to “Hardware Specifications” (page 94) in the “Appendix”
chapter.

Built-in AIT-5 drive (LIB-81/A5 models)

Built-in AIT-4 drive (LIB-81/A4 models)

Built-in AIT-3 Ex drive (LIB-81/A3X models)

* Only supports read operations

Built-in AIT-3 drive (LIB-81/A3 models)

Built-in AIT-2 drive (LIB-81/A2 models)

AIT-5 mark

AIT-3 Ex mark

AIT-3 mark

AIT-4 mark

AIT-4 mark

AIT-3 Ex mark

AIT-2 mark

*

AIT-3 mark

AIT-3 Ex mark

AIT-2 Turbo mark

AIT-1 mark

*

AIT-1 Turbo mark

*

AIT-E Turbo mark

*

AIT-2 mark

AIT-1 mark

AIT-3 mark

AIT-2 mark

AIT-1 mark

«
...
9
10
11
12
13
...
»

Summary of Contents for StorStation LIB-81







































































































Reviews:

No comments

Related manuals for StorStation LIB-81

Brand: Husky Pages: 20

TrueNAS R Series

Brand: iXsystems Pages: 24

Brand: Transcend Pages: 24

Brand: Velleman Pages: 4

Brand: QPS Pages: 9

Brand: Facom Pages: 2

External hard disk

Brand: Medion Pages: 18

Brand: Addonics Technologies Pages: 9

Brand: ATI Technologies Pages: 24

Brand: Backyard Pages: 60

Brand: Alphacool Pages: 2

Brand: Husky Pages: 14

Brand: SanDisk Pages: 25

Brand: Samsung Pages: 1

Brand: IBM Pages: 2

Brand: morse Pages: 4

Brand: Bosch Pages: 20

Brand: Cisco Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands