Sony StorStation LIB-81 Operating Instructions Manual Download Page 10

Page: 10 / 102

Chapter 1 Introduction

SCSI connector 1

SCSI connector 2

For information about connecting the SCSI connectors, refer to “Connecting to
the Host Computer” (page 17) an d “Connecting SCSI Peripheral Devices” (page
19) in Chapter 2, “Installation”.

LAN Connector

Connect a 10Base-T/100Base-TX network cable here.

Bottom

DIP Switches for Setup

The default setting of the DIP switches is as follows. Use the DIP switches as is.

For details, refer to “Setting the DIP Switches” (page 18) in Chapter 2,
“Installation”.

System Structure

Generally, the library is connected to the host computer and used to control the
library from the host computer. Also, you can connect the library to the network
so that it can be configured and maintained through a browser.

Notes

• A SCSI host adapter card must be installed in the host computer.
• In order to configure and maintain the library through a browser, browser

software must be installed in the computer. The following operating systems
and browsers are compatible with the library.

Ethernet

SCSI

LIB-81

Control the
library.

Make library settings and
perform maintenance.

Host computer

Summary of Contents for StorStation LIB-81







































































































Search results

Summary of Contents for StorStation LIB-81

Reviews:

Related manuals for StorStation LIB-81

Brands by name

Popular brands

Sony StorStation LIB-81, Operating Instructions Manual

Search results

Summary of Contents for StorStation LIB-81

Reviews:

Related manuals for StorStation LIB-81

Brands by name

Popular brands