Sony StorStation LIB-81 Operating Instructions Manual Download Page 34 | Manualshive

Page: 34 / 102

background image

34

Chapter 3 Basic Usage

Chapter

Basic Usage

Overview

This chapter explains the control panel, basic settings, handling the cartridges,
element addresses assignments and daily maintenance.

Control Panel

The control panel can be used to configure the AIT library settings, the AIT
drive settings and the network settings. It can also be used to display individual
information about the AIT library.
This section explains operation of the control panel, the control buttons and
menu items.
For details on the menu and how to configure the settings, see each related
reference.

Caution

This document contains explanations for all LIB-81 models (A5, A4, A3X, A3,
A2, and A1). We have used LIB-81/A3 displays to illustrate the explanations.
The display of models other than the LIB-81/A3 differs slightly, but operation
is similar to the LIB-81/A3.

Usage of the Control Panel

The following tasks can be accomplished using the control panel:
• Configure AIT library and AIT drive-related settings
• Configure network related settings
• Display information related to the AIT library
• Test hardware

Note

Some of the setups and operations can be performed through a browser.
Refer to Chapter 6, “Library Administration Menu” (page 67).

«
...
32
33
34
35
36
...
»

Summary of Contents for StorStation LIB-81







































































































Reviews:

No comments

Related manuals for StorStation LIB-81

Brand: Gearwrench Pages: 9

Brand: 80/20 Pages: 3

Brand: garofalo Pages: 12

Travelstar 14GS

Brand: IBM Pages: 2

BARRACUDA ST32000542AS

Brand: Seagate Pages: 2

Brand: SonicWALL Pages: 2

Brand: Yardmaster Pages: 24

Brand: myToys Pages: 4

Brand: AA Products Pages: 8

Brand: Palram Pages: 81

Brand: Argosy Pages: 1

Brand: US Polymers Pages: 17

Brand: Clarke Pages: 2

Verbatim KW7002

Brand: Verbatim Pages: 2

SOEXTREME SUPERSPEED

Brand: DANE-ELEC Pages: 1

SuperServer 110C-FHN4T

Brand: Supermicro Pages: 108

Brand: Promise Technology Pages: 64

Brand: Adaptec Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands