Sony StorStation LIB-81 Operating Instructions Manual Download Page 98 | Manualshive

Page: 98 / 102

background image

98

Appendix

Error Code List

When an error occurs in the AIT library, an error code appears on the LCD
panel. The following is a list of error codes that are displayed on the LCD panel.
When an error code appears, contact your dealer.

Changer Manager Errors

Error code

Description

01000031

An internal error occurred in the library.

01000032

An internal error occurred in the library.

01000033

Access attempted to a non-existent AIT drive.
The AIT drive may not be connected correctly.

NVRAM Driver Error

Error code

Description

02000001

An internal error occurred in the library.

02000002

Could not read/write NVRAM.

Mechanical Manager Error
(Byte2:Axis, Byte1:Class, Byte0:SubClass)

Error code

Description

03010101

PickerAxis

Timeout occurred during Close Sensor Low
Wait.

03010201

PickerAxis

Timeout occurred during Open Sensor Low
Wait.

03010901

Picker sensor malfunction.

03010A01

PickerAxis

The tape check sensor is not normal.

03020101

SliderAxis

Timeout occurred during Origin Sensor Low
Wait.

03020102*

SliderAxis

Timeout occurred during Origin Sensor
High Wait.

03020201

SliderAxis

Timeout occurred during Position Sensor
Low Wait.

03020202

SliderAxis

Timeout occurred during Position Sensor
High Wait.

03020501*

SliderAxis

Destination not reached.

03020601

SliderAxis

Fine tuning not possible.

03020701

SliderAxis

Cartridge cannot be removed.

03020801

SliderAxis

Cartridge not properly inserted in the drive.

03050101

TableAxis

Timeout occurred during Origin Sensor Low
Wait.

03050102

TableAxis

Timeout occurred during Origin Sensor
High Wait.

03050201

TableAxis

Timeout occurred during Position Sensor
Low Wait.

03050202

TableAxis

Timeout occurred during Position Sensor
High Wait.

03050401

TableAxis

The Position Sensor is not normal.

«
...
96
97
98
99
100
...
»

Summary of Contents for StorStation LIB-81







































































































Reviews:

No comments

Related manuals for StorStation LIB-81

G-DRIVE mobile USB

Brand: G-Technology Pages: 18

Brand: G-Technology Pages: 34

Solid Stainless Steel Shelving

Brand: Omega Pages: 2

454L / 120 US GAL

Brand: Keter Pages: 12

Brand: 80/20 Pages: 3

RACK PRO MINI-SAS

Brand: OWC Pages: 12

G-SPEED SHUTTLE with Thunderbolt 3

Brand: G-Technology Pages: 8

GEAR 175-9872-4

Brand: Yukon Pages: 7

SOHORAID SR8-TB3

Brand: Stardom Pages: 29

Intellient Stick Pro 220

Brand: PQI Pages: 8

Brand: PQI Pages: 21

Brand: MCE Technologies Pages: 19

Brand: Verbatim Pages: 15

Brand: ZyXEL Communications Pages: 6

Brand: Meec tools Pages: 96

Brand: Digital Electronics Corporation Pages: 8

CHEETAH 9 ST19101DC

Brand: Seagate Pages: 56

Cheetah 9LP Series

Brand: Seagate Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands