Sony StorStation LIB-81 Operating Instructions Manual Download Page 100 | Manualshive

Page: 100 / 102

background image

100

Appendix

Other Messages

When the following messages appear, perform the prescribed actions.

* If the message “Drive information F8” appears on the display, the cartridge

being used may not be the correct one. Check the type of cartridge being used.
To remove the loaded cartridge, select “3. Move Tape” in the menu and move
the cartridge from the drive to the library slot. Select “2. Eject/Insert Tape”,
and then “1. Eject from Library” to remove the cartridge.

When the following messages appear, contact your dealer.

Warning Message

Description

Cleaning Request

The AIT drive needs cleaning. Refer to “Cleaning the AIT
Drive” (page 63).

Cleaning Tape at EOM The spent cleaning cartridge is set. Replace the spent

cleaning cartridge with a new one.

Clean failure

Cleaning failed. Repeat the cleaning procedure.

Warning Message

Description

Drive information
XX

If the XX code is 3x, 4x, 5x, or 72, insert a new AIT data
cartridge into the library after cleaning the drive.*
For details, refer to “Cleaning the AIT Drive” (page 63).
If the XX code is CE, see the explanation below.
If the XX code is a code other than those explained
above, contact your dealer.

Drive information
CE

or

Cleaning Tape at EOM

The cleaning cartridge is exhausted. Replace it with a
new one and clean the drive again.

Please check the
transport screw

The transport screw may still be fastened in place. Refer
to “Unpacking” (page 13).

Warning Message

Description

Threshold condition
Turn Table

The turn table has operated more than the specified
number of times.

Threshold condition
Slider

The slider has operated more than the specified number
of times.

Threshold condition
Picker

The picker has operated more than the specified number
of times.

Threshold condition
Shutter

The shutter has operated more than the specified number
of times.

Threshold condition
Drive Load

The cartridges have loaded in the drive more than the
specified number of times.

Threshold condition
Fan

The fan has operated more than the specified number of
times.

Fan 1 trouble

Fan 1 malfunction.

Fan 2 trouble

Fan 2 malfunction.

Fan 3 trouble

Fan 3 malfunction.

Fan 1-3 trouble

Fan 1, Fan 2 and Fan 3 malfunction.

«
...
98
99
100
101
102
»

Summary of Contents for StorStation LIB-81







































































































Reviews:

No comments

Related manuals for StorStation LIB-81

ShareCenter DNS-343

Brand: D-Link Pages: 12

Brand: IBM Pages: 2

Brand: RAID Pages: 108

System Storage TS2900

Brand: IBM Pages: 130

Brand: Eastwood Pages: 8

MiniStation HD-PF320U2

Brand: Buffalo Pages: 2

Brand: Far Tools Pages: 11

OmniStor 4900F Series

Brand: Rackable Systems Pages: 196

Brand: IBM Pages: 190

Brand: Backyard Pages: 60

Brand: Palmako Pages: 20

Brand: Hama Pages: 8

Brand: Vivo Pages: 8

Brand: Clarke Pages: 8

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands