Sony StorStation LIB-81 Operating Instructions Manual Download Page 19

Page: 19 / 102

Chapter 2 Installation

Press the power switch to turn off the power.

Use a pointed object such as a machinist’s screwdriver to change the
settings of the DIP switches.

Press the power switch to turn on the power.

Connecting SCSI Peripheral Devices

SCSI peripheral devices can be connected to the SCSI connectors of the AIT
library. The SCSI configuration of the library is as shown below. Connect the
devices according to the system environment.

Notes

• The default factory settings of the SCSI IDs are as follows.

- Library:

- AIT Drive: 1

• Do not use repetitive SCSI IDs.

Turning the Power On/Off

Turn the Power On

Turn on the AIT library power, then turn on the host computer power.

Library

SCSI Connector 1

Library
Controller

AIT Drive

SCSI Connector 2

Summary of Contents for StorStation LIB-81







































































































Search results

Summary of Contents for StorStation LIB-81

Reviews:

Related manuals for StorStation LIB-81

Brands by name

Popular brands

Sony StorStation LIB-81, Operating Instructions Manual

Search results

Summary of Contents for StorStation LIB-81

Reviews:

Related manuals for StorStation LIB-81

Brands by name

Popular brands