Sony StorStation LIB-81 Operating Instructions Manual Download Page 94 | Manualshive

Page: 94 / 102

background image

94

Appendix

• To turn off the power to the AIT library, perform the shutdown procedure

described in “Turn the Power Off” (page 21) in Chapter 2. After pressing the
front power standby switch, press the power switch on the rear of the AIT
library. When you shut down the AIT library from the control panel, the
internal mechanism moves to the appointed position, then the power enters the
standby state.

• Remove all the cables such as the power cable, the SCSI cable, the terminator

and the network cable.

• When packing, perform the unpacking procedure on “Unpacking” (page 13)

in Chapter 2 in reverse. Be sure to fasten the transport screw.

Hardware Specifications

Hardware

AIT Drive

LIB-81/A5: SDX-1100 series (1)
LIB-81/A4: SDX-900 series (1)
LIB-81/A3X: SDX-800 series (1)
LIB-81/A3: SDX-700 series (1)
LIB-81/A2: SDX-500 series (1)
LIB-81/A1: SDX-400 series (1)

Number of drives that can be installed

One drives

Number of cartridges that can be set

Maximum of 8 volumes

Data transfer rate (sustained, no compression)

LIB-81/A5 models

LIB-81/A4 models

LIB-81/A3X models

Cartridge

Transfer rate

AIT-5

24 MB/s

AIT-4

24 MB/s

AIT-3 Ex

18 MB/s

AIT-3

16 MB/s

Cartridge

Transfer rate

AIT-4

24 MB/s

AIT-3 Ex

18 MB/s

Cartridge

Transfer rate

AIT-3 Ex

18 MB/s

AIT-3

16 MB/s

AIT-2 Turbo

16 MB/s

AIT-2

16 MB/s

AIT-1 Turbo

16 MB/s

AIT-1

11 MB/s

AIT-E Turbo

6 MB/s

«
...
92
93
94
95
96
...
»

Summary of Contents for StorStation LIB-81







































































































Reviews:

No comments

Related manuals for StorStation LIB-81

Brand: IBM Pages: 230

Brand: Quantum Pages: 384

Brand: Tandberg Data Pages: 60

Brand: National Instruments Pages: 5

StorNext QD7000

Brand: Quantum Pages: 29

StoraXe PowerBooster GSS0608

Brand: ADS-tec Pages: 140

Brand: OCZ Pages: 3

Brand: Seagate Pages: 40

Brand: Homak Pages: 3

G2 R8000 3U WW ERM

Brand: HPE Pages: 3

Brand: Muscle Rack Pages: 2

Brand: Duratuf Pages: 17

TS7650 PROTECTIER DEDUPLICATION APPLIANCE

Brand: IBM Pages: 218

DataStation pocket q.ue

Brand: TrekStor Pages: 112

Brand: Beta Pages: 7

Brand: Geekworm Pages: 13

Brand: AA Products Pages: 2

MediaShare Wireless SD/USB device

Brand: Verbatim Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands