Sony StorStation LIB-81 Operating Instructions Manual Download Page 62

Page: 62 / 102

Chapter 5 Operating the AIT Drive

Chapter

Operating the AIT Drive

Overview

This chapter explains how to view information related to the AIT drive and how
to clean the AIT Drive.

Viewing Information Related to the AIT Drive

Using the Information Menu of the control panel, the following information
related to the AIT drive can be viewed:
• Vendor ID
• Product name
• Serial number
• Version

Note

Information related to the AIT drives can also be viewed through a browser.

At the status display, press the [MENU] button for two seconds.

Select “1.Information”, then press the [ENTER] button.

“Information” appears.

Select “2.Drive”, then press the
[ENTER] button.

The AIT drive information is
displayed.

Press the [CANCEL] button three times to return to the status display.

Information 12:34
1.Library
2.Drive

V/ID SONY
Name SDX-700C
S/N 12345678
Version 0100

Summary of Contents for StorStation LIB-81







































































































Search results

Summary of Contents for StorStation LIB-81

Reviews:

Related manuals for StorStation LIB-81

Brands by name

Popular brands

Sony StorStation LIB-81, Operating Instructions Manual

Search results

Summary of Contents for StorStation LIB-81

Reviews:

Related manuals for StorStation LIB-81

Brands by name

Popular brands