
6-18
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Address
00 to 14
15
16
17
18
19
1A
1B
1C
1D
1E
1F to 58
59
5A to 64
65
66
67
68
69
6A
6B to 70
71
72 to 80
81
82
83
84 to 90
91
92 to D3
D4
D5
D6 to D8
D9
DA to F5
F6
F7 to FF
Remark
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
3. E Page Table (NTSC (60i) & PAL (50i) modes)
Note1:
The data of page: 0, address: 10 must be “00”.
Note2:
Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F,
14, 19, 1E, 1F Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of E, F,
14, 19, 1E, 1F Page Data”).
Note3:
Perform this item in NTSC (60i) mode or PAL (50i) mode only
required.
2. Modification of E, F, 14, 19, 1E, 1F Page Data
If the E, F, 14, 19, 1E, 1F page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
Note:
Perform this item in NTSC (60i) mode or PAL (50i) mode only
required.
Modifying Method:
1)
Set the NTSC(60i)/PAL(50i) switch to the following position.
NTSC(60i) (NTSC(60i) mode)
PAL(50i) (PAL(50i) mode)
2)
Before changing the data, select page: 0, address: 01, and set
data: 01.
3)
When changing the E, F page data, select page: 0, address: 10,
and set data: 00.
4)
When changing the 14, 19, 1E, 1F page data, select page: 0,
address: 10, and set data: 01.
After completing the modification of 14, 19, 1E, 1F page data,
reset the data of this address to “00”.
5)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
6)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
7)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of E, F, 14, 19, 1E,
1F Page data
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
2
00
29
Set the data.
3
2
01
29
Set the data, and press PAUSE
button.
Table. 6-1-13.
Ver. 1.7 2007. 10