Sony BVP-570, Maintenance Manual

Page: 62 / 806

3-16 (E)
BVP-570
3-1. Setup Menu
3-1-6. System Config Menu
Page Ver. Item Settings Contents
PreKnee/ PreKnee1 XXX (
[XX]
) Adjusts the R, G or B pre-knee 1 level on the VA board.
Zebra R/G/B
Aperture XXX (
[XX]
) Adjusts the aperture compensation signal level. y)
White Clip XXX (
[XX]
) Adjusts the white clip level.
White Clip
[On]
, Off Turns the white clip function on and off.
Zebra 1 LEVEL, XXX (
[XX]
) Sets the center value and range for the zebra 1 signal detection.
RANGE
Zebra 2 LEVEL XXX (
[XX]
) Sets the detection value for the zebra 2 signal.
Z.DISP 1,2, 1&2 Selects a zebra signal to be displayed on the viewfinder.
1
: Zebra 1 signal
2 : Zebra 2 signal
1&2 : Both zebra 1 and 2 signals are displayed at the same time.
Test 1, 2,
[Off]
Selects a test signal to be output in setting each item on the
PreKnee/Zebra page.
1
: Outputs the sawtooth test signal
2 : Outputs the 3-step waveform test signal
Off : No test signal is output
VTR/CCU VTR R-Y XXX (
[XX]
) Adjusts the R-Y color-difference signal level.
VTR B-Y XXX (
[XX]
) Adjusts the B-Y color-difference signal level.
CCU Y SAMP XXX (
[XX]
) Adjusts the level of the sample pulse to be mixed with the Y signal.
CCU R-Y SYNC XXX (
[XX]
) Adjusts the level of the sync pulse to be mixed with the R-Y signal.
CCU B-Y SAMP XXX (
[XX]
) Adjusts the level of the sample pulse to be mixed with the B-Y signal.
RGB Offset XXX (
[XX]
) Adjusts the G signal level.
Test 1, 2,
[Off]
Selects a test signal to be output in setting each item on the VTR/
CCU page.
1
: Outputs the sawtooth test signal
2 : Outputs the 3-step waveform test signal
Off : No test signal is output
CB On,
[Off]
Turns on and off the camera color-bar signal to be output when setting
each item on the VTR/CCU page.
IRIS Level XXX (
[XX]
) Adjusts the auto-iris level.
APL Ratio XXX (
[XX]
) Sets the way the iris is automatically adjusted.
_ 99 (PEAK)
↔
99 (AVERAGE)
(Filter Set) 3200 K, 4300 K, Set when the color-temperature filter is assigned according to a user’s
1 or A 5600 K, 6300 K requirement
2 or B
x)
n The filter indication on the VF screen can not display correctly
3 or C the selected filter type if this item is improperly set
4 or D
Filter Disk
[AUTO]
, 1, 2 Set corresponding to the filter disc type built in the OHB
After setting, excute the Refernce File Store of the Reference
File menu without fail
AUTO: Automatically recognizes the type of built-in filter
1:
Recognizes the one filter is built in
2: Recognizes the two filters are built in
x) Factory setting is as follows:
OHB-450/450P/451/451P/T450WS/T450WSP OHB-455WS/455WSP/550/550P/550WS/550WSP
(One filter built-in) BVP-570WSPK
(Two filters built-in)
1 or A 3200 K 3200 K
2 or B 5600 K 3200 K
3 or C 5600 K 4300 K
4 or D 5600 K 6300 K
y) The adjustment value is cleared by turning off and on the power sequentially because it is the temporary setting value for adjustment.